What wood is needed to build a deck

The three common choices when it comes to wood decks are redwood, cedar and pressure-treated wood that can be made of various types of wood species. Redwood and cedar are both naturally insect and rot resistant and have a natural look, but each has its own inherent issues.

What is the best wood to build a deck?

Overall, our experts at Patio Productions recommend Cedar or Redwood as the best wood choice for outdoor decks. If you’re looking for a cheaper option, pressure treated wood is your next best option.

Should I use deck boards or 2x6?

2×6 is thicker and is stronger, but is also more expensive. Spacing between deck boards provide a few critical functions. The primary function is to drain water from the deck. Gaps that are narrow (1/8”), can catch debris, specifically on top of the joists, and can be difficult to clean out.

What materials do you need to build a wood deck?

Measuring and Layout Tools. …
Framing Squares and Speed Squares. …
Excavation Tools. …
Shovels. …
Pipe and Squeeze Clamps. …
Wrenches and Pry Bars. …
Fastening Tools. …
Nail Gun with Compressor.

What size lumber Do I need to build a deck?

For the deck surface, you can use 2x4s, 2x6s, or 5/4x6s. The 5/4 decking (pronounced “five-quarter”), available in cedar and pressure-treated fir, is 1 inch thick and 5-1/2 inches wide with rounded edges that make for a splinter-free surface. Cedar 1x lumber usually has one rough side and one smooth side.

Should deck joists be 2x6 or 2x8?

For upper-level decks, 2×10 is recommended as the minimum size to use for strong guard post connections. 2×6 joists should only be used on ground-level decks that do not require, and will not provide for, any guards. … Most decking is not strong enough to support longer spans than 16″.

How thick should deck boards be?

Common deck board thickness. The most commonly used thickness for deck construction is 1-1/4”. But you can also get boards 2” thick, while there are boards only ¾” thick. It depends on the material, how flexible it is, and its hardness rate.

How many boards do I need for a 12x12 deck?

You will need 18 boards of 2-by-6-inch lumber or nine 2-by-10 inch boards to build the joists, also known as the beams. You should purchase an additional 25 percent wood to allow for framing pieces and waste.

How many joists do I need for a 12x12 deck?

For example, a 12-foot x 12-foot deck of 5/4 x 6 pressure treated wood decking on 16 inches on center spacing of joists will require: A 12-foot long deck with joists 16 inches on center will require 10 joists.

What is the most common deck board size?

The most common or standard deck board width is 6-inch wide planks based on square-foot coverage, labor, and material cost.

Article first time published on

Should you leave a gap between deck boards?

Proper wood deck board spacing should have at least a 1/8 inch gap after the decking has dried out. If you install your wood or treated deck boards while they are still wet boards, then they should be attached without a gap between them.

Can you use 2x4 for a deck?

The short answer is yes. 2x4s can work for deck joists. However, they aren’t ideal for spanning long distances without bending or breaking, so you have some limitations. Choosing 2x4s for a low-sitting deck is perfect for keeping your feet out of the mud.

Do I need pressure treated wood for deck?

It’s better to use treated lumber and know your deck will be secure in a few years than try to use untreated wood for the supports and watch them rot away rapidly. … Pressure treated wood doesn’t release any gases or particulates that could harm you and your family.

Can I use 2x8 for deck joists?

2×8 for joists will be fine, with 16″ OC. Should use 2×10 for beams but 2×8 will be fine as well. If you are worried you can triple the 2×8 for the beams but double will be sufficient. You should put the beams at 7 and 14 feet out from the house, with the piers you should do 3 per beam with spacing of 1, 7, 13.

How many posts do I need for a 10x10 deck?

A freestanding 10′ x10′ deck needs 4 posts, supporting two pairs of 2-ply non-incised 2×8 beam, upgrading the beam to 3-ply using incised wood.

Can you use 2x10 for deck boards?

Editor’s Comment’s: There is certainly no problem using the 2x10s for any of the structural framing of the deck. Using 2×10 treated lumber for decking is another matter entirely.

Can I use 1x4 for decking?

Width of material: We recommend only 1×4, 5/4×4 or narrower boards. Never use 1×6 or 5/4×6 material in close to ground applications. Spacing between boards: You must allow space for your deck boards to expand when they take on moisture, as they will inevitably do when exposed to wet weather, rain or high humidity.

How wide should a deck be?

A good size deck starts at 12 feet by 12 feet but can be as small as 8 feet by 8 feet for limited specialty use, such as a sitting area or a barbeque area just outside of the kitchen. Also deck should be no larger than the largest room in the house and not exceed 20% of the house square footage.

How many joists do I need for a 16 foot deck?

For example, when you space joists 16″ apart — which is standard for residential decks — a deck spanning 9 1/2′ would require 2-by-6 joists, a 13′ deck would need 2-by-8 joists and a 16′ deck calls for 2-by-10 joists.

Can I use 2x8 for deck boards?

Q: Can I use 2×8 treated lumber as deck boards? A: No, that’s a not a good idea. Lumber wider than 6 inches should not be used as a flat surface. Wide, flat boards have a tendency to pool rain water, which can lead to cupping problems.

How thick should joists be on a deck?

Decking TypeActual Thickness (inches)Suggested On Center Joist Spacing (inches)Tropical Hardwoods 1×13/16”16”Thermally-Modified 5/41”16”Pressure Treated Pine 5/41”16”Western Red Cedar 5/41”16”

Can you use 4x4 for deck joists?

For most decks, 4×4 lumber is strong enough for structural posts. If a deck is raised more than 6 feet above the ground, codes may require 6×6 posts.

How far should posts be on a deck?

Layout and Footing Locations In general, posts should be spaced no more than 8 feet apart. Some builders position them every 4 feet for a completely rigid frame. The maximum distance between footings is determined by the size of your joist material.

How many footings do I need for a 12x16 deck?

A standard deck will need four footings parallel to the house, but they will need to be temporarily braced by 6 inch-by-6 inch posts. Using doubled boards, you will then need to build beams on the top row of the posts to frame the edges of the deck. These must be topped with adjustable post caps.

What is the cheapest way to build a deck?

Choose wood, but carefully: Untreated wood decks are generally the cheapest to install, but don’t forget long-term costs. Wood decks require yearly maintenance and deteriorate quickly if they don’t get it.

How do you stagger deck boards?

A common method for staggering a deck is to start the first row with a full plank, then cut one-third of the next row’s first board off the end. The row after that has an additional one-third cut off and then repeat when you get back to a full board.

How much should deck boards overhang?

How Much Overhang Should a Deck Board Have? The decking should overhang the joists between ¼ and 2 inches beyond the end joists and rim board.

Should deck boards be installed crown up or down?

Crown up is the preferred installation method, despite the potential for bark side down deck boards to experience shelling. Bark side down allows for the formation of a crown warp. Once the board forms a crown, there’s less potential for the wood to hold water, which could lead to the wood splintering and rotting.

Can I use regular lumber for a deck?

Yes, you can use untreated wood to build a deck, but not without preparing it first. You can’t, of course, pressure treat it yourself, but you will need to seal; the wood and stain/paint it to ensure the wood is ready to take on the harsh external weather.

Which is Better pressure-treated wood or cedar?

When it comes to comparing treated wood vs. cedar, pressure-treated wood is the sturdier and more weather-proof of the two. It’s highly resistant to insect attack and rot, and special versions rated for “ground contact” can be buried in soil and will continue to shrug off decay for decades.

Why is treated lumber cheaper than untreated?

Affordability. Pressure-treated wood is notably cheaper than cedar, redwood, and other types of wood. And, because of its durability, you’re much less likely to experience a need for costly repairs in the future. It is a great choice for those operating on a smaller budget.